It has come to my attention that a way to limit the request range size
would be useful in general, for reasons beyond just speeding up initial
header parsing.
This patch generalizez -initial_request_size to -request_size. I decided
to continue allowing both options to be used simultaneously, so users can
e.g. set -request_size to something large like 10 MiB, but still use a smaller
size for initial header parsing (e.g. 256 KiB).
Fixes: https://github.com/mpv-player/mpv/issues/8655
Sometimes, HTTP sources require a lot of seeking during probing / header
parsing (especially for formats like MXF). Currently, we need to completely
tear down and re-establish the connection most times this happens, which puts
a lot of stress on the network stack and also results in transmission of
possibly many unnecessary bytes.
This patch adds an option to allow FFmpeg to request partial ranges during
the initialization stage. This is done until the initial request size is fully
read, after which we fall back to the normal behavior (i.e. infinite streaming
via an unbounded request).
The usefulness of this is limited without also specifying -multiple_requests 1,
since otherwise there is little point to requesting partial ranges to begin
with. (However, it is semantically independent, so we keep it that way.)
Previously, the pkt_size option only affected write buffering in the file
protocol. This change extends its effect to read mode as well.
On embedded systems with limited RAM, users can now reduce I/O buffer
memory by setting a smaller pkt_size.
Signed-off-by: caifan3 <caifan3@xiaomi.com>
Add a "pkt_size" AVOption to the Unix domain socket protocol. This option
allows the user to specify the maximum packet size for packet-oriented
sockets (SOCK_DGRAM and SOCK_SEQPACKET).
Signed-off-by: caifan3 <caifan3@xiaomi.com>
Note that this changes the code to work the same way as other protocols where
an URL parameter can override an AVOption.
Signed-off-by: Marton Balint <cus@passwd.hu>
429 and 503 codes can, and often do (e.g. all Google Cloud
Storage URLs can), return a Retry-After header with the error,
indicating how long to wait, asd either a date, or in seconds,
before retrying again. If it is not respected by, for example,
using our default backoff stratetgy instead, chances of success
are very unlikely.
Some references:
* https://datatracker.ietf.org/doc/html/rfc6585
* https://datatracker.ietf.org/doc/html/rfc7231#section-7.1.3
This adds an AVOption to respect that header.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
add option named rtmp_enhanced_codec,
it would support hvc1,av01,vp09 now,
the fourcc is using Array of strings.
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
We shouldn't be providing links to unverified and non-FFmpeg-controlled
content in our documentation.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
We do not endorse or recommend specific third party servers or companies
that users' data will be funneled through.
It is also incorrectly describing how FFmpeg currently works.
Should have been part of 412922cc6f but was
missed.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Introduce fifo_size and overrun_nonfatal params to configure fifo buffer
behavior.
Use newly introduced RIST_DATA_FLAGS_OVERFLOW flag to check for overrun
and error out in that case.
Signed-off-by: Marton Balint <cus@passwd.hu>
This patch adds support for:
- ffplay ipfs://<cid>
- ffplay ipns://<cid>
IPFS data can be played from so called "ipfs gateways".
A gateway is essentially a webserver that gives access to the
distributed IPFS network.
This protocol support (ipfs and ipns) therefore translates
ipfs:// and ipns:// to a http:// url. This resulting url is
then handled by the http protocol. It could also be https
depending on the gateway provided.
To use this protocol, a gateway must be provided.
If you do nothing it will try to find it in your
$HOME/.ipfs/gateway file. The ways to set it manually are:
1. Define a -gateway <url> to the gateway.
2. Define $IPFS_GATEWAY with the full http link to the gateway.
3. Define $IPFS_PATH and point it to the IPFS data path.
4. Have IPFS running in your local user folder (under $HOME/.ipfs).
Signed-off-by: Mark Gaiser <markg85@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
And forward it to the underlying UDP protocol.
Fixes ticket #7517.
Signed-off-by: Jiangjie Gao <gaojiangjie@live.com>
Signed-off-by: Marton Balint <cus@passwd.hu>
Add the "http_proxy" option and its handling to the "tls" protocol,
pass the option from the "https" protocol.
The "https" protocol already defines the "http_proxy" command line
option, like the "http" protocol does. The "http" protocol properly
honors that command line option in addition to the environment
variable. The "https" protocol doesn't, because the proxy is
evaluated in the underlying "tls" protocol, which doesn't have this
option, and thus only handles the environment variable, which it
has access to.
Fixes#7223.
Signed-off-by: Moritz Barsnick <barsnick@gmx.net>
Signed-off-by: Marton Balint <cus@passwd.hu>
Also remove AV_LOG_SIMULATE from the list as it is not used directly, and do
not use panic level on unknown loglevel, but make them warn. Also fix mapping of
NOTICE/INFO/VERBOSE and add documentation about when the option should actually
be used.
Signed-off-by: Marton Balint <cus@passwd.hu>
Maximum packet size is 10000 (RIST_MAX_PACKET_SIZE, which is unfortunately
private) minus the RIST protocol overhead which is 28 bytes for the unencrypted
case, 36 for the encrypted case.
Signed-off-by: Marton Balint <cus@passwd.hu>
